TACHOMETER Oil Temperature Amp Fuel GAUGE SET Compatible with INT IH 240 Utility

This tachometer and four gauge set listing fits a International 240 Utility tractor.

This tachometer assembly has a 5/8" UNF cable end. Tachometer also comes with 6 volt light feature option! You can use or choose not to! 

The International part number it replaces is 371277R92. The diameter is 3 3/8" (85mm).

This temperature gauge replaces: IH part numbers 353868R91, 53690R2, 369849R91, 393476R91

This gauge has Yellow Zinc "Cad" Plating for corrosion resistance protection! This gauge also has mounting studs and bracket, rubber gasket seal for mounting flush to dash. It has a 6V light feature included so owner has option to use or not to use!

Temperature is measured in 3 zones. Black face with white lettering and colored zones to gauge temperature. Water temp gauge includes a 72" oem style spring covered capillary lead. 5/8-18 U.F. END W/ 1/2" NPT PIPE BUSHING.

This oil pressure gauge replaces: IH part numbers 362039R93, 362177R94 and 536696R2.

****I also sell a Farmall IH Tractor Oil Pressure Gauge Copper Tubing Line Kit! This will make easy installation.****

This gauge has Yellow Zinc "Cad" Plating for corrosion resistance protection! This gauge also has a 1/8" NPT male fitting, mounting studs and bracket, rubber gasket seal for mounting flush to dash. It has a 6 volt light feature included so owner has option to use or not to use!  

This amp gauge replaces IH part numbers: 360053R91, 378424R91 and 393334R1

This gauge has Yellow Zinc "Cad" Plating for corrosion resistance protection! This gauge also has mounting studs and bracket, rubber gasket seal for mounting flush to dash. It has a 6 volt light feature included so owner has option to use or not to use!

**If you need 12 volt light bulb let me know at time when you pay!**

Fuel Gauge: 371056R91 Also Fits 371056R92

 Fits Farmall / IH Tractors International 240 

 2" / 52mm Dashboard Hole, This is for a Rochester style gauge, 0-70 Ohm's. Will not work with Stewart Warner sending unit (32 Ohm full to 244 Ohm empty) Gauge works with 6 or 12 volts 

Before you buy this gauge and then install the fuel gauge: Get a good electrical manual for your machine from the manufacture. You need to be 100% sure of your fuel gauge wiring circuit is 100% correct! and whether or not the correct sending unit is in the existing fuel tank examples: universal sending unit with improper ohms and or wiring, custom units because original is no longer available, other manufactures have different ohms.(a lot of things happen to these tractors in 60 years, I see it on the restorations that I do from time to time). I can not return so called defective electrical units to manufacture that are hooked up incorrectly. I will only take gauge back if it has not been installed and you pay the shipping! Or If it is TRULY DEFECTIVE!! Most of the sales are without issues because proper installation has been followed. I am a 33 year ASE Master Tech myself and I run into a lot of splicing and rewiring of tractors. Also other different parts used from other models.

From what I am told and what I have found out on my own 240's is that the gauge sending unit is not available for these 240's. I am informed that the gauge sending unit that will work for these 240's is purchased through local Case IH dealers. It is for a 444 or 2444 fuel tank and was part # 84270826. It costs about $60.00. Look it up on Case IH's website.  If you use this one keep in mind that one of the bolt holes is located off a little bit so it fits only one way when mounted.

This gauge has Yellow Zinc "Cad" Plating for corrosion resistance protection! This gauge also has mounting studs and bracket, rubber gasket seal for mounting flush to dash. It has a 6 volt light feature included so owner has option to use or not to use!

Disclaimer:

Tractor America parts listed are Aftermarket parts and not manufactured by the (OEM) Original Equipment Manufacturer. Original manufacturers names, logos, part descriptions and numbers are for reference purpose only. This does not intend, indicate and or suggest that our parts are manufactured by the original equipment manufacturer(s).

All Tractor Aftermarket listed parts are "Compatible with" will "Fit" and or made "For":  Farmall, IH, International Harvester, Ford, Allis Chalmers, Massey Ferguson, Massey Harris, Oliver, Cockshutt, Minnieapolis Moline, Willys, MB, jeep, Case-IH, Case, David Brown, John Deere, JD, Kubota, New Holland, NH, Avery, Long, White, Perkins, Volvo, Oregon, Leyland, Iveco, Fiat, Honda, Exmark, Stihl, K&N, MTD, Scag, Wright MFG., Murray, Wizard, Western Auto, Troy Built, Rally, Cub-Cadet, Ariens, Atlas, Techumseh, Husqvarna, Bobcat, E-Z-Go, AYP, Fiat Hesston, NGK, Champion,  Hinomoto, Deutz Allis, GM, Chevrolet, Craftsman, Poulan, Mitsubishi, Uniiversal, McCormick, CNH, MTD, Yanmar. 

IHUT240

IHTMP72

IHO362039R93SM

IHA360053R91

IHF371056R91